Levelling (Correction in Levelling, Distance of Visible Horizon, Reciprocal Leveling, ETC)

  Levelling  

It is the method of determining the difference of elevation or level of different points on earth’s surface. If all the heights of different points are measured related to a plane, the plane is termed a datum plane. In general this datum plan is taken to be mean sea level (MSL), to standardize the measured to height Internationally.

  Important Terminologies In Levelling  

leveling-Elevation - Altitude

Elevation & Altitude

  • If the vertical distance of the point is above or below the datum surface is noted as Elevation.
  • It is the vertical distance of a point above MSL i.e when datum is MSL, the elevation is termed as Altitude.

Note- If the datum surface is MSL then elevation is the same as attitude.

Reduced Level

Elevation of a point with respect to mean sea level is called reduced levels. And the process of determining the difference in reduced level of the point is called and levelling.

Mean Sea Level

It is the mean data of sea fluctuation considered at Mumbai. It is used as datum/reference to find reduced levels. The value of mean sea level as a datum is obtained by averaging the elevation of high and low tides, at several points for a long period of time about 19 years.

Bench Marks(B.M)

The benchmark is a fixed point of known elevation above the datum. Any point whose elevation is definitely known can be used as a bench mark.

The following type of bench marks are established and used.

1.G.T.S Bench Marks

The great trigonometrical survey (G.T.S) bench marks are those which are established by the survey of India which very high accuracy throughout the country.

2.Permanent Bench Marks

The permanent benchmark are those which are established on a permanent structure. These bench marks are established by PWD or survey of India.

3.Temporary Bench Marks

These are the bench marks established temporarily whenever required.

4.Arbitrary Bench Marks

These are the bench marks whose elevation are arbitrary assumed for levelling of a small area.

  Measurement in Leveling Work  

 Leveling Work

Horizontal Line

Line setup by an instrument keeping the bubble at centre is called horizontal line. This line is always tangent to the earth surface.

Vertical Line

It is a line from any point on the earth’s surface to the center of earth. Ex- Plumb line.

Level Line

It is an imaginary line considered to parallel M.S.L. Level line perpendicular to the plumb line.

Back Sight Reading

On first reading taken from instrument position are called back sight reading. It is always taken to benchmark.

Fore Sight- Back Sight- Intermediate Sight Reading

Fore Sight Reading

The last reading taken from instrument position are called fore sight reading. After fore sight reading either instrument is shifting or the work is closed.

Intermediate Sight Reading

All other reading except back sight & fore sight are called intermediate sight reading.


  Method to Find Reduced Level  

Assumption

  • Survey is Plane
  • Effect of earth curvature is not considered.

For computation of reduced level of various point, two method are used:

  1. Height  of Instrument
  2. Rise and Fall method

Reduced Level min

Height of Instrument

The first reading is always back sight.
The last reading is alway fore sight.
HI= RL of BM + BS
RL at any point= HI – Staff Reading
ΣBS- ΣFS = Last RL – First RL

Rise and Fall Method

RL of any point= RL of previous point + Rise(-Fall).
ΣRise – ΣFall = Last RL- First RL.
ΣRise – ΣFall = Last RL- First RL = ΣBS- ΣFS


  Inverted Staff 

Some time leveling staff is inverted in levelling work to find the Reduced level of ceiling, arches, beam etc.
Inverted staff readings are represented with -ve sign.

Inverted Staff

 

  Correction Required in Levelling Work  

1.Correction due to Earth Curvature (Cc)

Staff reading should be taken corresponding to levelling but it is found corresponding horizontal line.
Net difference between horizontal line and level line is called correction due to earth curvature.

Correction Required in Levelling Work

(R+Cc)= R2 + d2

R2+Cc2 + 2·R·Cc = R2 + d2

Cc (Cc + 2·R) = d2 Cc<<< 2R,  so: Cc+2R≈ 2R

Cc (2·R) = d2

\(Cc=\frac{d^{2}}{2R}\) {Cc→km, d2→km2, R→km}

This correction is always (-ve) negative.

\(Cc=\frac{d^{2}}{2\times 6370}\times 1000\).

\(Cc=-0.0785d^{2}\)

Cc in meter, d in Kilometer

2.Correction due to Refraction (CR)

Due to the effect of refraction line of sight is shifted in downward direction due to which lesser reading is obtained in staff hence this correction is always +ve in nature.
Magnitude of this correction is taken as 1/7 of correction due to earth curvature.

\(C_R=\frac{1}{7}(0.0785d^{2})\)

CR= +0.0112d2.

CR in meter, d in Kilometer

3.Combined Correction due to Both (C)

C= Cc + CR

C= Cc + CR

C= -0.0785d2 + 0.0112d2

C= -0.0673d2

C in meter, d in Kilometer

Note

In staff reading = h

Correct staff reading = h-0.0673d2


  Distance of Visible Horizon   

Maximum distance visible from any height is called distance of visible horizon.

Distance of Visible Horizon

Case.1 When height of any one point is considered.

H= C= 0.0673d2

Distance of visible horizon \(d=\sqrt{\frac{H}{0.0673}}=3.855\sqrt{H}\)

\(d= 3.855\sqrt{H}\)d→km, H→m

Case.2 When height of both points are considered.

D = d1+d2

Distance of visible horizon \(d= 3.855\left ( \sqrt{h_1}+ \sqrt{h_2} \right )\)

d→km, h1→m, h2→m

  Reciprocal Leveling  

This technique of leveling work is used to find the exact height difference between two points on the opposite banks of a river or a deep gorge.

By Reciprocal leveling

  • Effect of curvature, Refraction & collimation ( Collimation means bubble in center but not horizontal) are eliminated.
  • Collimation error can be found.

Procedure
To point A,B are selected on opposite site of obstruction and staff reading taken the both station keeping the instrument first near station A and then near station B.

 Reciprocal-Leveling

Case.1 When the instrument near A

Staff reading at A = hA
Staff reading at B = hB

error e in the staff reading on B
Corrected staff reading B= hB-e
Height  different between A & B
H= (hB- e)- hA —(1)

e= error due to curvature, collimation, refraction.

Case.2 When the instrument near B

Staff reading at A = hA’
Staff reading at B = hB’

error e in the staff reading on A
Corrected staff reading A= hA’ – e
Height  different between A & B
H= hB‘ – (hA‘-e) —(2)

From equation 1 & 2
H= (hB – e) – hA  —(1)
H= hB’- (hA’- e) —(2)
Equation 1+2
2H= (hB-hA) + (hB’-hA’)

Exact height difference H

H= \(\frac{(hB-hA) + ({hB}’-{hA}’)}{2}\)

RLB = RLA– H.

RL= Reduced level of B

RL= Reduced level of A

H = height difference between A & B


  Collimation error  

It is a type of instrumental error due to which the line of Collimation is not horizontal even if the bubble is at centre.

Collimation error

 

Measured staff reading at B= hB
True staff Reading at B should be = hA+ H
Error = E= hB – (hA+H).

Case.1 When Area is Large

Error= ECURVATURE + EREFRACTION + ECOLLIMATION

Ec+ ER + Ecl = hB- (hA+H)Ec= -0.0112d2
ER= +0.0785d2

Case.2 When Area is small

Effect of curvature & refraction are neglected

Ec+ ER + Ecl= hB- (hA+H)Ec →0, E→0

Ecl = hB- (hA+H)

If Ecl is -ve then Light of sight shifts in downward direction.
If Ecl is +ve then Light of sight shifts in upward direction.

Angular / Inclination Error

\(\theta = tan^{-1}\left ( \frac{E_{\text{cl}}}{d} \right )\)


  Sensitivity of Bubble Tube 

Angle of rotation given to the telescope due to just one division movement of the bubble inside the bubble tube is called sensitivity. Activeness of bubbles is called sensitivity. The sensitivity is expressed as second/division. If not mentioned the length of the division should be taken as 2 mm.

Sensitivity of Bubble Tube

Sensitivity

\(\alpha =\frac{\theta }{n}\).

\(\alpha =\frac{l }{R}=\frac{S}{nD}\) Radian.

π Rad= 180°

1 rad= \(\frac{180° }{π}×60×60\) = 206265 second.

Sensitivity

\(\alpha =\frac{l}{R}×206265 \) second.

\(\alpha =\frac{S}{nD}×206265\) second.

l= length of one division of bubble tube
R= radius of curvature of bubble tube
S= staff intercept (different b/w staff reading)
D= Distance from instrument to staff
n= number of division

The sensitivity of level tube increases with 

  1. Increase in radius (R)
  2. Increase in length (l)
  3. Increase in smoothness at internal surface
  4. Increase in diameter
  5. Decrease in viscosity of liquid.
  6. Decrease in roughness at internal surface

FOR MORE INFORMATION ABOUT SURVEYING

1 thought on “Levelling (Correction in Levelling, Distance of Visible Horizon, Reciprocal Leveling, ETC)”

  1. Thankyou sir,
    Aapke in notes se kaafi help hui h SURVEYING complete krne m.
    Please mere request h ki jlde se aap baki importank subjects b complete krde.
    Thankingyou

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top